View STM1818TWX7F_7288873.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

september 2010 doc id11464 rev 8 1/25 1 stm1810 stm1811 stm1812 stm1813 stm1815 stm1816 stm1817 stm1818 low power reset circuit features precision monitoring of 3 v, 3.3 v, and 5 v supply voltages four output configurations: ? push-pull, active-high (stm1812,1817) ? push-pull, active-low (stm1810,1815) ? open-drain, active-low (stm1811,1816) ? open-drain, active-low with push-button detect (stm1813,1818) reset pulse width - 100 ms (min.) low supply current - 4 a (typ.) guaranteed assertion down to v cc = 1.0 v (0 c to 105 c) factory-trimmed reset thresholds of 2.55 v, 2.88 v, 3.06 v, 4.37 v, and 4.62 v (typ.) power supply transient immunity push-button/manual reset detect (stm1813/1818) operating temperature: ?40 c to 105 c 2.5% reset threshold accuracy: (?40 c to 105 c) available in the sot23-3 package fully compatible with ds181x and mxd181x products. sot23-3 (wx) table 1. device summary order codes 5 v 3.3 v/ 3.0 v active-low reset (push-pull) active-low reset (open-drain) active-high reset (push-pull) active-low reset (open-drain, bidirectional, with mr detect) stm1810l/m ?? stm1811l/m ?? (1) stm1812l/m ?? stm1813l/m ? ? stm1815t/s/r ?? stm1816t/s/r ?? (1) stm1817t/s/r ?? stm1818t/s/r ?? 1. active-low rst with internal pull-up resistor. www.st.com
contents stm1810/1811/1812/1813/1815/1816/1817/1818 2/25 doc id11464 rev 8 contents 1 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 functional block diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2 pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2.1 active-low rst output (push-pull) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2.2 active-low rst output (open-drain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2.3 active-high rst output (push-pull) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.2.4 active-low rst output (open-drain with internal 5.5 k pull-up) with manual reset detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.2.5 v cc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.2.6 v ss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.1 reset output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.2 push-button detect reset (stm1813/1818) . . . . . . . . . . . . . . . . . . . . . . . . 9 2.3 interfacing to bidirectional microcontrollers (mcu?s) . . . . . . . . . . . . . . . . . 9 2.4 negative going v cc transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.5 valid rst output down to v cc = 0 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3 typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4 maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5 dc and ac parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.1 ecopack ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7 part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 8 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
stm1810/1811/1812/1813/1815/1816/1817/1818 list of tables doc id11464 rev 8 3/25 list of tables table 1. device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table 2. signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 table 3. stm1810/stm1815 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 4. stm1811/stm1816 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 5. stm1812/stm1817 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 6. stm1813/stm1818 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 7. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 8. operating and ac measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 9. dc and ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 table 10. sot23-3 ? 3-lead small outline transistor package mechanical data. . . . . . . . . . . . . . . . . 21 table 11. ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 table 12. marking description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 table 13. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
list of figures stm1810/1811/1812/1813/1815/1816/1817/1818 4/25 doc id11464 rev 8 list of figures figure 1. logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 figure 2. sot23-3 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 3. hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 4. push-pull active-low output (stm1810/1812/1815/1817) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 5. open-drain, active-low output (stm1811/1816) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 6. open-drain, active-low output (bidirectional, manual reset detect, stm1813/1818) . . . . . . 7 figure 7. reset timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 figure 8. push-button manual reset with mr detect (stm1813/1818) . . . . . . . . . . . . . . . . . . . . . . . 10 figure 9. manual reset timing diagram, switch bounce/debounce (stm1813/1818) . . . . . . . . . . . . . 11 figure 10. interfacing mcus with bidirectional reset pins (rst , open-drain, stm1811/1816) . . . . . . 11 figure 11. valid reset (rst ) output down to v cc = 0 v (push-pull). . . . . . . . . . . . . . . . . . . . . . . . . . . 11 figure 12. valid reset (rst) output down to v cc = 0 v (push-pull). . . . . . . . . . . . . . . . . . . . . . . . . . . 12 figure 13. supply current vs. temperature (no load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 figure 14. normalized reset time-out period (t rec ) vs. temperature - v od = v th ? v cc . . . . . . . . . . . 13 figure 15. v cc -to-reset output delay vs. temperature - v od = v th ? v cc . . . . . . . . . . . . . . . . . . . . . 14 figure 16. voltage output low vs. i sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 figure 17. voltage output high vs. i source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 figure 18. normalized reset threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 figure 19. max. transient duration not causing reset pulse vs. reset threshold overdrive. . . . . . . . . 16 figure 20. ac testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 21. sot23-3 ? 3-lead small outline transistor package outline . . . . . . . . . . . . . . . . . . . . . . . . 20
stm1810/1811/1812/1813/1815/1816/1817/1818 description doc id11464 rev 8 5/25 1 description stm181x devices are low power reset devices used to monitor power supplies for microcontrollers. they perform a single function: asserting a reset signal whenever v cc supply voltage drops below a preset value and keeping it asserted until v cc has risen above the preset threshold for a minimum period of time (t rec ). they provide excellent circuit reliability without additional external components when used with +3.0 v / +3.3 v (stm1815?stm1818), and +5 v (stm 1810?stm1813) power supply systems. a precision voltage reference and comparator monitors the v cc input for an out-of-tolerance condition. when an invalid v cc condition occurs, the reset output (rst ) is forced low (or high in the case of rst) and remains asserted for t rec after v cc rises above the reset threshold. the stm1813/1818 also keep reset asserted for t rec after the output is momentarily pulled to ground by an external push-button switch. the stm1812 and stm1817 have an active-high, push-pull output. the stm1810 and stm1815 (push-pull) and stm1811, stm1813, stm1816, and stm1818 (open-drain) have an active-low rst output. the open-drain devices (stm1811 / stm1813 / stm1816 / stm1818) also have an internal pull-up resistor to v cc . the stm1813 and stm1818 feature a debounced manual reset feature that asserts a reset if the rst pin is pulled low for more than 1.5 s. when used to initiate manual reset, rst debounces signals from devices such as mechanical switches. for devices with this feature, the release of the external switch triggers the reset period. the stm181x devices are guaranteed to output the correct logic state for v cc down to 1.0 v (0 c to +105 c). they also provide a reset comparator designed to ignore fast transients on v cc . reset thresholds are available between +2.55 v and +4.62 v. these small, low power devices are ideal for use in portable equipment. all are available in the space-saving 3-pin sot23 package, and are specified from ?40 c to +105 c. figure 1. logic diagram 1. for stm1812, stm1817. !) 6 ## 34-x 6 33 234234
description stm1810/1811/1812/1813/1815/1816/1817/1818 6/25 doc id11464 rev 8 figure 2. sot23-3 connections 2. rst for stm1812 and stm1817. figure 3. hardware hookup 1. rst for stm1812 and stm1817 (see table 1 ). 2. only valid for stm1813 and stm1818. table 2. signal names symbol description v ss ground rst active-low reset output rst (1) 1. for stm1812, stm1817. active-high reset output v cc supply voltage and input for reset threshold monitor !) 234234 6 33 6 ## !)a 6 ## 6 33 6 ## -#5 34-x 234 6 ## 6 33 2eset )nput 0ush button reset
stm1810/1811/1812/1813/1815/1816/1817/1818 description doc id11464 rev 8 7/25 1.1 functional block diagrams figure 4. push-pull active-low output (stm1810/1812/1815/1817) 1. rst for stm1812 and stm1817. figure 5. open-drain, active-low output (stm1811/1816) 1. 5.5 k internal pull-up resistor. figure 6. open-drain, active-low output (bidirectional, manual reset detect, stm1813/1818) 1. 5.5 k internal pull-up resistor. 1.2 pin descriptions see figure 1 and ta b l e 2 for a brief overview of the signals connected to this device. 1.2.1 active-low rst output (push-pull) pulses low when v cc drops below v rst , and stays low as long as v cc is below the reset threshold. it remains low for t rec after v cc rises above the reset threshold. 1.2.2 active-low rst output (open-drain) pulses low when v cc drops below v rst , and stays low as long as v cc is below the reset threshold. it remains low for t rec after v cc rises above the reset threshold. rst output has an internal 5.5 k pull-up resistor. !)a #/-0!2% 6 234 6 ## t rec generator 234 !) #/-0!2% 6 234 6 ## t rec generator 234 !) #/-0!2% 0ush button detect 6 234 6 ## t rec generator 234
description stm1810/1811/1812/1813/1815/1816/1817/1818 8/25 doc id11464 rev 8 1.2.3 active-high rst output (push-pull) pulses high when v cc drops below v rst , and stays high as long as v cc is below the reset threshold. it remains high for t rec after v cc rises above the reset threshold. 1.2.4 active-low rst output (open-drain with internal 5.5 k pull-up) with manual reset detect pulses low when v cc drops below v rst , or rst is externally pulled low for at least 1.5 s. it remains low for t pbrst after v cc rises above the reset threshold, or after the external manual reset is released (see figure 9 ). rst output has an internal 5.5 k pull-up resistor. 1.2.5 v cc supply voltage and input for v rst comparator. 1.2.6 v ss ground, is the reference for the power supply . it must be connected to the system ground. table 3. stm1810/stm1815 pin name function 1rst active-low reset output (push-pull) 2v cc supply voltage and input for reset threshold monitor 3v ss ground table 4. stm1811/stm1816 pin name function 1rst active-low reset output (open-drain, with internal 5.5 k pull-up resistor) 2v cc supply voltage and input for reset threshold monitor 3v ss ground table 5. stm1812/stm1817 pin name function 1 rst active-high reset output (push-pull) 2v cc supply voltage and input for reset threshold monitor 3v ss ground table 6. stm1813/stm1818 pin name function 1rst active-low reset output (open-drain, with internal 5.5 k pull-up) with push- button/manual reset detect 2v cc supply voltage and input for reset threshold monitor 3v ss ground
stm1810/1811/1812/1813/1815/1816/1817/1818 operation doc id11464 rev 8 9/25 2 operation 2.1 reset output the stm181x asserts a reset signal to the microcontroller (mcu) whenever v cc goes below the reset threshold (v rst ), and is guaranteed valid down to v cc = 1.0 v (0 c to 105 c). a microcontroller?s (mcu) reset input starts the mcu in a known state. the stm1810 - stm1813/ stm1815 - stm1818 low power reset circuits assert reset to prevent code-execution errors during power-up, power-down, and brownout conditions ( figure 7 ). during power-up, once v cc exceeds the reset threshold an internal timer keeps rst low for the reset time-out period, t rec . after this interval, rst returns high. if v cc drops below the reset threshold, rst goes low. each time rst is asserted, it stays low for at least the reset time-out period. any time v cc goes below the reset threshold, the internal timer clears. the reset timer starts when v cc returns above the reset threshold. reset t rec is also triggered by an externally initiated rising edge on the rst pin (stm1813/stm1818), following a low signal of 1.5 s minimum duration. 2.2 push-button detect reset (stm1813/1818) many systems require push-button reset capability ( figure 8 ), allowing the user or external logic circuitry to initiate reset. on the stm1813/stm1818, a logic low on rst held for greater than 1.5 s asserts a reset. rst deasserts following a 100 ms minimum reset time- out delay (t rec ). a manual reset input shorter than 1.5 s may release rst without the 100 ms minimum reset time-out delay. to facilitate use with mechanical switches, the stm1813/stm1818 contain internal debounce circuitry. a debounced waveform is shown in figure 9 the rst output has an internal 5.5 k pull-up resistor. 2.3 interfacing to bidirectional microcontrollers (mcu?s) as the rst output on the stm1811/stm1816 is open-drain, these devices interface easily with mcu?s that have bidirectional reset pins. connecting the p supervisor?s reset (rst ) output directly to the microcontroller?s reset (rst ) pin allows either device to assert reset ( figure 10 ). no external pull-up resistor is required, as it is within the stm1811/stm1816. 2.4 negative going v cc transients the stm181x are relatively immune to negative-going v cc transients (glitches). figure 19 shows typical transient duration versus reset comparator overdrive (for which the stm181x will not generate a rese t pulse). the graph was generat ed using a negative pulse applied to v cc, starting at 0.5 v above the actual reset threshold and ending below it by the magnitude indicated (comparator overdrive). the graph indicates the maximum pulse width a negative v cc transient can have without causing a reset pulse. as the magnitude of the transient increases (further below the threshold), the maximum allowable pulse width decreases. any combination of duration and overdrive which lies under the curve will not generate a reset signal. typically, a v cc transient that goes 100 mv below the reset threshold and lasts 20 s or less will not cause a reset pulse. a 0.1 f bypass capacitor mounted as close as possible to the v cc pin provides additional transient immunity.
operation stm1810/1811/1812/1813/1815/1816/1817/1818 10/25 doc id11464 rev 8 2.5 valid rst output down to v cc = 0 v when v cc falls below 1 v, the rst output no longer sinks current, but becomes an open circuit. in most systems this is not a problem, as most mcus do not operate below 1 v. however, in applications where rst output must be valid down to 0 v, a pull-down resistor may be added to hold the rst output low (see figure 11 ). this resistor must be large enough to not load the rst output, and still be small enough to pull the output to ground. a 100 k resistor is recommended. note: the same situation applies for the active-high rst of the stm1810/1812. a 100 k pull-up resistor to v cc should be used if rst must remain valid for v cc < 1.0 v. figure 7. reset timing diagram 1. rst for stm1812 and stm1817. figure 8. push-button manual reset with mr detect (stm1813/1818) !) 234 234 6 ## 6 234 6 ## min t rec t rec !) 6 ## 34- 34- 234 0ush button2%3%4 6 ## 6 33 -icro2%3%4 2eset monitor
stm1810/1811/1812/1813/1815/1816/1817/1818 operation doc id11464 rev 8 11/25 figure 9. manual reset timing diagram, switch bounce/debounce (stm1813/1818) figure 10. interfacing mcus with bidirectional reset pins (rst , open-drain, stm1811/1816) figure 11. valid reset (rst ) output down to v cc = 0 v (push-pull) 1. ~100 k resistor recommended. !) 234 6 ## %xternal push button t 0"234 #losed /pen t 0"234 3witchbounce !) 6 ## 34- 34- 234 6 ## 6 33 6 33 6 ## -#5 234 input !) 6 ## 2 0 34- 34- 234 6 ## 6 33 6 33 6 ## -#5 234 input
operation stm1810/1811/1812/1813/1815/1816/1817/1818 12/25 doc id11464 rev 8 figure 12. valid reset (rst) output down to v cc = 0 v (push-pull) 1. ~100 k resistor recommended. !) 6 ## 2 0 34- 34- 234 6 ## 6 33 6 33 6 ## -#5 234 )nput
stm1810/1811/1812/1813/1815/1816/1817/1818 typical operating characteristics doc id11464 rev 8 13/25 3 typical operating characteristics typical values are at t a = 25 c. figure 13. supply current vs. temperature (no load) figure 14. normalized reset time-out period (t rec ) vs. temperature - v od = v th ? v cc 4emperature?# !)b n n 6 ## 6 6 ## 6 3upplycurrent?! 4emperature?# .ormalizedresettime outperiodms !)b n n
typical operating characteristics stm1810/1811/1812/1813/1815/1816/1817/1818 14/25 doc id11464 rev 8 figure 15. v cc -to-reset output delay vs. temperature - v od = v th ? v cc figure 16. voltage output low vs. i sink 4emperature?# !)b n n /utputcurrentm! /utputvoltage6 !)b
stm1810/1811/1812/1813/1815/1816/1817/1818 typical operating characteristics doc id11464 rev 8 15/25 figure 17. voltage output high vs. i source figure 18. normalized reset threshold vs. temperature /utputcurrentm! 6 ## 6 /54 6 !)b 6 ## 6 4emperature?# .ormalizedresetthreshold !)b n n
typical operating characteristics stm1810/1811/1812/1813/1815/1816/1817/1818 16/25 doc id11464 rev 8 figure 19. max. transient duration not causing reset pulse vs. reset threshold overdrive 1. reset occurs above the line. 2esetthresholdoverdrivem6 !)b
stm1810/1811/1812/1813/1815/1816/1817/1818 maximum rating doc id11464 rev 8 17/25 4 maximum rating stressing the device above the rating listed in ta b l e 7 may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the ?operating? sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. refer also to the stmicroelectronics? ?sure program? and other relevant quality documents. table 7. absolute maximum ratings symbol parameter value unit t stg storage temperature (v cc off) ?55 to 150 c t sld (1) 1. reflow at peak temperature of 255 c to 260 c for < 30 seconds (total thermal budget not to exceed 180 c for between 90 to 150 seconds). lead solder temperature for 10 seconds 260 c v io input or output voltage ?0.3 to v cc +0.3 v v cc supply voltage ?0.3 to 7.0 v i o output current 20 ma p d power dissipation 320 mw
dc and ac parameters stm1810/1811/1812/1813/1815/1816/1817/1818 18/25 doc id11464 rev 8 5 dc and ac parameters this section summarizes the operating measurement conditions, and the dc and ac characteristics of the device. the parameters in the dc and ac characteristics tables that follow, are derived from tests performed under the measurement conditions summarized in ta b l e 8 . designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. figure 20. ac testing input/output waveforms table 8. operating and ac measurement conditions parameter stm1810 - 1818 unit v cc supply voltage 1.0 to 5.5 v ambient operating temperature (t a ) ?40 to 105 c input rise and fall times 5ns input pulse voltages 0.2 to 0.8 v cc v input and output timing ref. voltages 0.3 to 0.7 v cc v !) 6 ## 6 ## 6 ## 6 ##
stm1810/1811/1812/1813/1815/1816/1817/1818 dc and ac parameters doc id11464 rev 8 19/25 table 9. dc and ac characteristics sym. alter- native description test condition (1) min. typ. max. unit v cc operating voltage t a = 0 to +105 c 1.0 5.5 v t a = ?40 to +105 c 1.2 5.5 v i cc v cc supply current v cc = 3.6 v, no load 4 10 a v cc = 5.5 v, no load 9 16 a v ih input high voltage stm1813/1818 only 0.7 v cc v v il input low voltage stm1813/1818 only 0.4 v v oh output high voltage 0 < i oh < 500 a v cc ? 0.5 v cc ? 0.1 v i oh rst output source current v cc v rst (max.), reset not asserted (stm1810/stm1815) 350 a rst output source current v cc v rst (min.), reset asserted (stm1812/stm1817) 350 a i ol rst output sink current v cc 2.7 v, reset asserted, v out = 0.4 v (stm1810/1811/1813/1815/1816/1818) 10 ma rst output sink current v cc 2.7 v, reset not asserted, v out = 0.4 v, (stm1812/1817) 10 ma c out output capacitance (2) 10 pf reset thresholds v rst reset threshold stm181xl 25 c 4.62 v ?40 to 105 c 4.50 4.75 v stm181xm 25 c 4.37 v ?40 to 105 c 4.25 4.49 v stm181xt 25 c 3.06 v ?40 to 105 c 2.98 3.15 v stm181xs 25 c 2.88 v ?40 to 105 c 2.80 2.97 v stm181xr 25 c 2.55 v ?40 to 105 c 2.47 2.64 v t rd v cc to rst delay v cc = (v th + 100 mv) falling to (v th ? 200 mv) 25s t rec rst pulse width v cc rising 100 150 200 ms push-button reset detect (stm1813, stm1818) t pb push-button detect to rst stm1813/1818 1.5 s t pbrst push-button rst time-out from rising edge 100 150 200 ms internal pull-up resistance stm1811/1816 3.5 5.5 7.5 k stm1813/1818 3.1 5.5 7.5 k 1. valid for ambient operating temperature: t a = ?40 c to 105 c; v cc = 1.2 v to 5.5 v (except where noted). 2. the stm1811/1813/1816/1818 have an internal pull-up resistor which may sink 1 ma of current.
package mechanical stm1810/1811/1812/1813/1815/1816/1817/1818 20/25 doc id11464 rev 8 6 package mechanical 6.1 ecopack ? in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. figure 21. sot23-3 ? 3-lead small outline transistor package outline 1. drawing is not to scale. 3/4 # ! ! ! 8 # # , , # e $ e 8b % - #!" " % ! - # ! "
stm1810/1811/1812/1813/1815/1816/1817/1818 package mechanical doc id11464 rev 8 21/25 table 10. sot23-3 ? 3-lead small outline transistor package mechanical data symbol mm inches typ. min. max. typ. min. max. a 0.89 1.12 0.035 0.044 a1 0.01 0.10 0.001 0.004 a2 0.88 1.02 0.035 0.042 b 0.30 0.50 0.012 0.020 c 0.08 0.20 0.003 0.008 d 2.80 3.04 0.110 0.120 e 2.10 2.64 0.083 0.104 e1 1.20 1.40 0.047 0.055 e 0.89 1.03 0.035 0.041 e1 1.78 2.05 0.070 0.081 l 0.54 0.021 l1 0.40 0.60 0.016 0.024 q 0 8 0 8 n3 3
part numbering stm1810/1811/1812/1813/1815/1816/1817/1818 22/25 doc id11464 rev 8 7 part numbering table 11. ordering information scheme note: contact the local st sales office for availability. for other options, or for more information on any aspect of this device, please contact the st sales office nearest you. example stm1810 l wx 7 f device type stm181x reset threshold voltage stm1810 - 1813 l = v rst = 4.50 v to 4.75 v (4.62 v typ.) m = v rst = 4.25 v to 4.49 v (4.37 v typ.) stm1815 - 1818 t = v rst = 2.98 v to 3.15 v (3.06 v typ.) s = v rst = 2.80 v to 2.97 v (2.88 v typ.) r = v rst = 2.47 v to 2.64 v (2.55 v typ.) package wx = sot23-3 temperature range 7 = ?40 to 105 c shipping method f = ecopack package, tape and reel
stm1810/1811/1812/1813/1815/1816/1817/1818 part numbering doc id11464 rev 8 23/25 table 12. marking description part number reset threshold output topside marking (1) 1. x = letter assigned to indicate assembly work week (i.e., a = ww01 and ww02, b = ww03 and ww04, c = ww05 and ww06..., z = ww51, ww52, and ww53). stm1810l 4.62 v push-pull rst 9aax stm1810m 4.37 v push-pull rst 9abx stm1811l 4.62 v open-drain rst 9ahx stm1811m 4.37 v open -d rain rst 9ajx stm1812l 4.62 v push-pull rst 9aqx stm1812m 4.37 v push-pull rst 9arx stm1813l 4.62 v open -d rain rst 9axx stm1813m 4.37 v open -d rain rst 9ayx stm1815t 3.06 v push-pull rst 9bgx stm1815s 2.88 v push-pull rst 9bhx stm1815r 2.55 v push-pull rst 9bjx stm1816t 3.06 v open -d rain rst 9bpx stm1816s 2.88 v open -d rain rst 9bqx stm1816r 2.55 v open -d rain rst 9brx stm1817t 3.06 v push-pull rst 9bwx stm1817s 2.88 v push-pull rst 9bxx stm1817r 2.55 v push-pull rst 9byx stm1818t 3.06 v open -d rain rst 9cdx stm1818s 2.88 v open -d rain rst 9cex stm1818r 2.55 v open -d rain rst 9cfx
revision history stm1810/1811/1812/1813/1815/1816/1817/1818 24/25 doc id11464 rev 8 8 revision history table 13. document revision history date revision changes 26-aug-04 1.0 first issue. 05-oct-04 2.0 update reset characteristics, add typical graphs, remove sc70 references ( figure , 1 , 3 , 6 , 10 , 11 , 13 , 14 , 15 , 16 , 17 , 18 , 19 ; and 20 , table 9 , 11 , and 12 ). 19-nov-04 3.0 update dimensions ( ta ble 1 0 ). 07-dec-04 4.0 remove some voltage options ( ta b l e 1 , 10 , 11 , and 12 ). 29-jun-05 5.0 temperature range change ( figure 13 , 14 , 15 , and 18 ; ta b l e 8 , 9 , and 11 ). 11-oct-05 6.0 update typical operating characteristics, lead-free text ( figure 13 , 14 , 15 , 16 , 17 , 18 , and 19 ; table 11 , and 12 ). 28-aug-2007 7 document reformatted. update ta b l e 1 2 . 02-sep-2010 8 document reformatted, updated section 6.1: ecopack ? , corrected typo in ta b l e 9 , table 11 and ta b l e 1 2 .
stm1810/1811/1812/1813/1815/1816/1817/1818 doc id11464 rev 8 25/25 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at an y time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in military, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2010 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of STM1818TWX7F

	To Download STM1818TWX7F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .